Can-Fan Max-Fan Inline Fans – 12" Fan

Can-Fan Max-Fan Max-Fans are in line mixed-flow fans capable of jaw-dropping performance at high static pressure through innovative design. The Max-Fan is the first fan that has been developed with a Computational Fluid Dynamics (CFD) program. CFDs are used for engineering aircraft propulsion engines. The perfectly designed 3D blades of the impeller and stator make this fan extremely powerful and energy efficient. Compared with other inline fans, the efficiency is 50%-100% higher. 6″-14″ come pre-wired with an 8 ft 120 V power cord. Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan® is a more powerful and efficient fan that takes less energy to run. The Can Fan Max-Fans are available in a wide range of sizes 120 Volt Can-Fan Max-Fan 6″ 334 CFM Can-Fan Max-Fan 8″ 667 CFM Can-Fan Max-Fan 8″ HO 932 CFM – 3 Speed Can-Fan Max-Fan 10″ 1019 CFM Can-Fan Max-Fan 12″ 1708 CFM Can-Fan Max-Fan 14″ 1700 CFM 240 Volt Volt Can-Fan Max-Fan 10″ 240V 1100 CFM Can-Fan Max-Fan HO “The Beast” 14″ 240V 3343 CFM Can-Fan Max-Fan 16″ 240V 2436 CFM Can-Fan Max-Fan 18″ 240V 3665 CFM Can-Fan Max-Fan 20″ 240V 4688 CFM The 240 Volt Max-Fans can bring energy efficiency to larger systems. These high-powered Max-Fans™ potentially save hundreds of dollars each year in energy costs using a lightweight aluminum housing. Comes with a 6 ft power cord (240 V). Detailed specifications & recommended Can Fan Filters for all Max Fans are near the bottom of this page. All Can Fan Inline Fans are speed controllable. The 12" Max-Fan required the use of the variable transform controller. Only use a speed or motor control of the proper amperage to adjust the speed of the fans. Details Manufactured in Germany Extremely energy efficient Optimized mixed flow is quieter than comparable fans Very high aerodynamic efficiency Lower operational cost than traditional centrifugal fans Easy installation 5-year warranty Determining your requirement - Exhaust vs Recirculating (Scrubbing) You will need to determine whether or not you are exhausting (going from a contaminated environment to a sterile environment in only a single pass through the filter) or recirculating, aka “scrubbing” (exhausting the system back into the contaminated space). Exhaust In an exhaust setting the air only passes through the filter one time so it is imperative that we remove as close to 100% of the contaminate as possible with that one chance. This requires that the contaminant have a certain time in contact with the carbon in order to be fully adsorbed. Our filters are marked with both exhaust and recirculating ratings for just this reason. If you are using this system to exhaust, DO NOT exceed the exhaust rating for the filter, the more this rating is exceeded the less contaminant will be adsorbed because the two will not have enough contact timefor adsorption to fully take place. Recirculating In a recirculating system, the contact time is not such a crucial number as we are taking contaminated air, filtering it, and releasing it back into what is typically and constantly decontaminated environment. It is for this reason that it is not necessary to remove 100% of the contaminant in a single pass. Instead we double the exhaust rating which will reduce the contact time, the goal here is to still remove a large portion of the contaminant but to get raise the cycle rate of air through the filter above the rate of emission from the source. Now, instead of removing 99.9% of the contaminant in a single pass we are getting closer to 60% but we are getting twice as many cycles through the filter in the same amount of time and over time, reducing the overall build-up of contaminant in the environment. Sizing Your Space Once you’ve determined the type of system you need, it’s time to size your space. Typically for exhaust we recommend a simple length x width x height /3 calculation. This will give you the amount of air (cubic feet per minute, CFM) that you will need to move to properly ventilate your space allowing for a three-minute air exchange (all the air in the space is exchanged for fresh air every three minutes). This is the number you will match your filter to. Example: Room size: 10’x12’x8’ (960 cubic feet) 960 cubic feet / 3 minutes = 320CFM (Minimum recommended CFM to exchange the air every 3 minutes) For recirculating systems, you can use the same length x width x height but divide by 1.5. This will give you a high cycle rate while still ensuring the removal of a majority of contaminant with each pass through the filter. Model Specifications Can-Fan Max-Fan 8″ 667 CFM CFM: 667 at 0wg RPM: 3250 Maxx Watts: 179 Amps: 1.5 @ 120v AC 60 Hz Diameter 8" Outside Diameter: 30.5 cm / 12″ Length: 8.875″ Blade Design: Mixed Flow Housing: Plastic Inlet/Outlet 8″ Recommended Filters Recirculating Can-Lite 8×25 Can 66 Can 50 Can-Lite 8×40 Exhaust Can 75 Can 100 Can 125 Can-Fan Max-Fan 8″ HO 932 CFM – 3 Speed Speed High Medium Low CFM: 932 at 0wg 849 at 0wg 749 at 0wg RPM: 2935 2705 2460 Maxx Watts: 213 188 178 Amps: 1.87 @ 120v AC 60 Hz 1.71 @ 120v AC 60Hz 1.62 @ 120v AC 60Hz Diameter 8" Outside Diameter: 30.5 cm / 12″ Length: 8.875″ Blade Design: Mixed Flow Housing: Plastic Inlet/Outlet 8″ Recommended Filters Recirculating Can-Lite 8×25 Can 66 Can 50 Can-Lite 8×40 Can 75 Exhaust Can 100 Can 125 Can 1505 Can-Fan Max-Fan 10″ 1019 CFM CFM: 1019 at 0wg RPM: 2990 Maxx Watts: 228 Amps: 1.9 @ 120v AC 60 Hz Sones: 11.5 at 0.10 wg Diameter 10" Length: 8.5″ Blade Design: Mixed Flow Housing: Galvanized Inlet/Outlet 10″ Recommended Filters Recirculating Can 50 Can 75 Can-Lite 8×40 Exhaust Can 100 Can 125 Can 150 Can-Fan Max-Fan 12″ 1708 CFM CFM: 1708 at 0wg RPM: 3374 Maxx Watts: 489 Amps: 4.1 @ 120v AC 60 Hz Diameter 12" Length: 12.125″ Blade Design: Mixed Flow Housing: Galvanized Inlet/Outlet 12″ Recommended Filters Recirculating Can 75 Can 100 Can-Lite 12x40 Can 125 Can 150 Exhaust Can-Lite 14×50 XL Can-Fan Max-Fan 14″ 1700 CFM CFM: 1786 at 0wg RPM: 1700 Maxx Watts: 253 Amps: 2.1 @ 120v AC 60 Hz Sones: 10 at 0.10wg Diameter 14" Length: 15.75″ Blade Design: Mixed Flow Housing: Galvanized Inlet/Outlet 14″ Recommended Filters Exhaust Can 150 Can-Lite 14×50 XL Recirculating Can 100 Can 125 Can-Lite 14x40 240 Volt models Can-Fan Max-Fan 10″ 240 Volt CFM: 1100 at 0wg RPM: 2990 Maxx Watts: 160 Amps: 0.8 @ 234v AC 50 Hz Max Ambeint Temp: 50˚C / 122˚F Diameter 10" Length: 8.5" Blade Design: Mixed Flow Housing: Galvanized Inlet/Outlet 10″ Recommended Filters Exhaust Can 100 Can 125 Can 150 Exhaust Can 50 Can 75 Can-Lite 14x40 Can-Fan Max-Fan HO “The Beast” 14″ 240 Volt 3343 CFM CFM: 3343 at 0wg Maxx Watts: 960 Amps: 5.4 @ 240v AC 50 Hz Diameter 14" Max Ambeint Temp: 45˚C / 105˚F Length: 15.75″ Blade Design: Mixed Flow Housing: Galvanized Inlet/Outlet 14″ Recommended Filters Recirculating Max 2500 Can 150 Can-Lite 14×50 XL Can-Fan Max-Fan 16″ 240 Volt 2436 CFM CFM: 2436 at 0wg RPM: 1680 Maxx Watts: 347 Amps: 1.5 @ 240v AC 60 Hz Max Ambeint Temp: 80˚C / 176˚F Diameter 16" Length: 16.375″ Blade Design: Mixed Flow Housing: Aluminum Inlet/Outlet 16″ Recommended Filters Recirculating Max 2500 Can-Fan Max-Fan 18″ 240V 3665 CFM CFM: 3665 at 0wg RPM: 1680 Maxx Watts: 700 Amps: 3.0 @ 240v AC 60 Hz Max Ambeint Temp: